3
PM50CSD120
Intellimod™ Module
Three Phase IGBT Inverter Output
50 Amperes/1200 Volts
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
Electrical and Mechanical Characteristics, T
j
= 25°C unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Units
Control Sector
Over Current Trip Level OC T
j
= 25°C93157 — Amperes
(V
D
= 15V) T
j
= 125°C59——Amperes
Short Circuit Trip Level SC -20°C ≤ T
j
≤ 125°C, V
D
= 15V — 183 — Amperes
Over Current Delay Time t
off(OC)
V
D
= 15V — 10 — µS
Over Temperature Protection (V
D
= 15V) OT Trip Level 111 118 125 °C
(Lower Arm) OT
R
Reset Level — 100 — °C
Supply Circuit Under Voltage Protection UV Trip Level 11.5 12.0 12.5 Volts
(-20 ≤ T
j
≤ 125°C) UV
R
Reset Level — 12.5 — Volts
Circuit Current I
D
V
D
= 15V, V
CIN
= 15V, V
N1
-V
NC
—4055mA
V
D
= 15V, V
CIN
= 15V, V
XP1
-V
XPC
—1318mA
Input ON Threshold Voltage V
CIN(on)
Applied between U
P
-V
UPC
, V
P
-V
VPC
, 1.2 1.5 1.8 Volts
Input OFF Threshold Voltage V
CIN(off)
W
P
-V
WPC
, U
N
, V
N
, W
N
-V
NC
1.7 2.0 2.3 Volts
Fault Output Current* I
FO(H)
V
D
= 15V, V
CIN
= 15V — — 0.01 mA
I
FO(L)
V
D
= 15V, V
CIN
= 15V — 10 15 mA
Minimum Fault Output Pulse Width* t
FO
V
D
= 15V 1.0 1.8 — mS
*Fault output is given only when the internal OC, SC, OT and UV protections schemes of either upper or lower arm device operate to protect it.
Thermal Characteristics
Characteristic Symbol Condition Min. Typ. Max. Units
Junction to Case Thermal Resistance R
th(j-c)Q
Each IGBT — — 0.38 °C/Watt
Inverter Part R
th(j-c)F
Each FWDi — — 0.70 °C/Watt
R
th(j-c´)Q
Each IGBT** — — 0.23
†
°C/Watt
R
th(j-c´)F
Each FWDi** — — 0.36
†
°C/Watt
Contact Thermal Resistance R
th(c-f)
Case to Fin Per Module, — — 0.027 °C/Watt
Thermal Grease Applied
**T
C
measured point is just under the chips.
†
If you use this value, R
th(f-a)
should be measured just under the chips.
Recommended Conditions for Use
Characteristic Symbol Condition Value Units
Supply Voltage V
CC
Applied across P-N Terminals 0 ~ 800 Volts
Control Supply Voltage*** V
D
Applied between V
UP1
-V
UPC
, 15 ± 1.5 Volts
V
N1
-V
NC
, V
VP1
-V
VPC
, V
WP1
-V
WPC
Input ON Voltage V
CIN(on)
Applied between U
P
-V
UPC
, V
P
-V
VPC
,0 ~ 0.8 Volts
Input OFF Voltage V
CIN(off)
W
P
-V
WPC
, U
N,
V
N
, W
N
-V
NC
4.0 ~ V
D
Volts
PWM Input Frequency f
PWM
Using Application Circuit 0 ~ 20 kHz
Minimum Dead Time t
DEAD
Input Signal ≥ 3.0 µS
***With ripple satisfying the following conditions: dv/dt ≤ ± 5v/µs, Variation ≤ 2V peak to peak.
(10 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales